Buy Cheap Dremel 290-05 120-Volt Industrial Engraver From Here Now!
290-05 Style: Inc. (3) 9924 Carbide Engraving Points, Price Each This item features: -Stroke adjustment dial regulates engraving depth. -Light and compact design for precision engraving. -Engraves metal, glass, wood, plastic, and ceramics. -Soft grip has been added to provide extra control and comfort. -Packed in a plastic tube. -Voltage: 115.00 VAC. -Frequency: 60.0 Hz. -Cycle Rate: 7200 strokes/min [Max]. -Power Source: Electric. -Wt.: 0.85 lb.
Readmore
Technical Details
- Amperage: 0.2 Amps- Hertz: 60 Hz
- Speed: 7,200 spm
- Voltage: 115 V AC, 60Hz
See more technical details
By Moderate American Man (Arizona, USA)
I have used Inscriblio engravers, poor quality chinese engravers, and now this Dremel engraver. The Dremel is easily the highest quality, and best value. My only complaint is that it's size and shape make it harder to use then the other light weight engravers. However I think I will get used to it, and it seems obvious that it will last much, much longer then either of the other engravers I have used in the past.
By Jamie R. Deem (Orlando, FL)
I bought this engraver to mark all of my tools with serial numbers and my name. On the very first tool, after engraving the serial number, the diamond tip began to loosen and slip out. I reached for the included little wrench with a standard screwdriver tip on one end to tighten the set screw that holds the diamond tip in the tool. I tried to use the screwdriver tip to tighten the slotted set screw and quickly discovered that the provided tool was too thick to fit into the groove in the set screw. I was a little miffed, but just walked over to a benchtop polishing wheel to remove a small amount of steel from the tool so that it would fit in the screw for which it was made. When I returned to the engraver to tighten the set screw the tool fit perfectly, and with one turn the screw, all the threads stripped out of the tool, not off the set screw. The set screw is just fine, but the metal that was threaded for it to go into is made of a metal so soft that it cannot withstand a single turn of the set screw that is essential to hold the diamond tip in place. I'm still rather incredulous that this tool would be made so poorly; perhaps they had a bad batch that got out on the market. If you already have one, with a soft metal housing for the diamond tip, you might wish to try some Locktite on the set screw and perhaps even the diamond tip where it contacts the soft metal housing. Be sure to take note of the different strengths of Locktite so that the bottle or tube you buy will be effective. My engraver will be going back, and I do not think I will be purchasing any more Dremel products in the near future.
By A. Walk
I have only used this tool a few times, but it has worked very well.
I was surprised at how thick of a piece of metal it will make a cut in.
By Licari Woodworking, LLC (ct)
great little unit! works on all metals including saw blades and router bits. I am using the diamond tip with it. powerfull and not too loud. glad i own it.
Images Product
Buy Dremel 290-05 120-Volt Industrial Engraver Now
Buy Dremel 290-05 120-Volt Industrial Engraver |
Cheap Dremel 290-05 120-Volt Industrial Engraver | Low Price Dremel 290-05 120-Volt Industrial Engraver | Best Dremel 290-05 120-Volt Industrial Engraver | Order Dremel 290-05 120-Volt Industrial Engraver | Good Dremel 290-05 120-Volt Industrial Engraver | Lowest Dremel 290-05 120-Volt Industrial Engraver | Save Dremel 290-05 120-Volt Industrial Engraver | Discount Dremel 290-05 120-Volt Industrial Engraver | Purchase Dremel 290-05 120-Volt Industrial Engraver | Shop Dremel 290-05 120-Volt Industrial Engraver | Buying Dremel 290-05 120-Volt Industrial Engraver | Where Dremel 290-05 120-Volt Industrial Engraver
0 comments:
Post a Comment